SETUP & SITE HAZARDS • CRANE EXAM TOPIC

What Is a Controlled Access Zone?
CAZ, Swing Radius & Fall Zone

What a controlled access zone is, and how it differs from the restricted areas around a crane: the swing radius and the fall zone.

Reviewed November 2026 against 29 CFR 1926.502(g), 1926.500(b), 1926.1424, 1926.1425.

A controlled access zone (CAZ) is an area where certain work, such as overhand bricklaying or leading edge work, may be done without guardrails, personal fall arrest or safety nets, and where access is controlled. It is marked by a control line. It is a fall protection rule, not a crane rule. Around a crane, the restricted areas are the swing radius and the fall zone.

Four Restricted Areas, Compared

AreaWhat it isWho may be insideRule
Controlled access zone (CAZ)Area near an unprotected edge where listed work is done without conventional fall protectionOnly employees doing that work1926.502(g)
Controlled decking zone (CDZ)Steel erection area over 15 and up to 30 feet above a lower level where metal decking is first being installedOnly employees doing leading edge decking work1926.760(c)
Swing radius hazard areaArea the crane's rotating superstructure sweeps where a worker could be struck or crushedTrained, authorized personnel, and only after telling the operator1926.1424(a)
Fall zoneArea, including but not limited to directly under the load, where suspended material could foreseeably fallOnly employees hooking, unhooking or guiding the load, making the initial connection, or operating a concrete hopper or bucket1926.1425

Control Line Rules for a CAZ

ItemRequirement
Leading edge workControl line 6 to 25 feet from the unprotected or leading edge
Precast concrete erection6 feet to 60 feet, or half the length of the member being erected, whichever is less
Overhand bricklaying10 to 15 feet from the working edge
MarkingFlagged or clearly marked at intervals of 6 feet or less
HeightLowest point at least 39 inches, highest point no more than 45 inches (50 inches for overhand bricklaying)
StrengthMinimum breaking strength of 200 pounds

Source: 29 CFR 1926.502(g).

What Crane Operators Need From This

Swing radius. Where the rotating upper could strike or pinch someone, the employer must train the people working nearby and put up control lines, warning lines, railings or similar barriers. Before anyone goes into that area out of the operator's view, they tell the operator, and the operator does not rotate until told they are clear.

Fall zone. While the load is not moving, nobody is in the fall zone except those hooking, unhooking, guiding or making the initial connection. When they are, the load must be rigged by a qualified rigger, rigged to prevent unintended displacement, and hooks must have self-closing latches or the equivalent. When a load is being landed, only the workers needed to receive it may be in the fall zone.

5 Practice Questions: Controlled access zone

From the question bank in the app. Pick an answer, then open the explanation. For a scored test, try the NCCCO core practice test.

Definitions

1. The 'fall zone' is defined as…

  1. AThe area, including beneath the load, where suspended materials could foreseeably fall in an accident
  2. BA 10-foot circle around the outriggers
  3. CThe swing path of the counterweight
  4. DThe area behind the crane cab
Show answer

Answer: A. The area, including beneath the load, where suspended materials could foreseeably fall in an accident. The fall zone includes but is not limited to the area directly beneath the load — anywhere partially or completely suspended material could reasonably land.

General Knowledge

2. According to OSHA 1926.1425, when employees are engaged in hooking, unhooking, and guiding the load in the fall zone, what type of hook must be used?

  1. Ahooks with self-closing latch
  2. Bsorting hook
  3. Cswivel hooks
  4. Dhooks with self-lubrication swivel
Show answer

Answer: A. hooks with self-closing latch. OSHA 1926.1425 requires hooks with self-closing latches when employees work with loads in the fall zone.

General Knowledge

3. According to OSHA 1926.1425, which of the following individuals are NOT allowed within the fall zone?

  1. Aqualified evaluator
  2. Boperator of a concrete bucket
  3. Cemployee guiding the load
  4. Demployee unhooking the load
Show answer

Answer: A. qualified evaluator. OSHA 1926.1425 permits only employees essential to the operation (hooking, unhooking, guiding, and similar) in the fall zone; a qualified evaluator is not one of them.

Rigging

4. While a load is being landed, who is permitted inside the fall zone?

  1. AOnly employees needed to receive the load
  2. BAnyone wearing a hard hat
  3. CThe entire rigging crew
  4. DNo one, without exception
Show answer

Answer: A. Only employees needed to receive the load. Only employees needed to receive a load are permitted within the fall zone when a load is being landed.

Site Setup

5. According to OSHA 1926.1424, which area around a crawler crane must always be barricaded?

  1. Athe crane's rear swing radius
  2. Bthe crane's matting area
  3. Cthe crane's boom length
  4. D10% of the working radius
Show answer

Answer: A. the crane's rear swing radius. OSHA 1926.1424 requires the area within the rotating superstructure's rear swing radius to be barricaded to prevent workers from being struck or crushed by the counterweight.

Study the Whole Exam, Not 20 Questions

5,000+ practice questions across Core and every specialty, load chart trainers with the rating table on screen, timed exam simulations, and the pass guarantee.

Controlled access zone: Questions & Answers

What is a controlled access zone?
An area in which certain work, such as overhand bricklaying, may take place without guardrail systems, personal fall arrest systems or safety net systems, and access to the zone is controlled. That is the definition in 29 CFR 1926.500(b).
Is a controlled access zone the same as a crane barricade?
No. A CAZ is a fall protection measure near an unprotected edge. The barricade around a crane marks the swing radius hazard area under 1926.1424.
How far back is a controlled access zone control line?
6 to 25 feet from the edge for leading edge work, 10 to 15 feet for overhand bricklaying, and 6 to 60 feet (or half the member length if less) for precast concrete erection.
What is the fall zone on a crane lift?
The area, including but not limited to directly beneath the load, where partially or completely suspended materials could reasonably be expected to fall in an accident.
What is a controlled decking zone?
A steel erection area over 15 and up to 30 feet above a lower level where metal decking is initially being installed. It is a separate rule in Subpart R, 1926.760(c).

This page is a study aid. It summarizes federal OSHA rules and industry standards and is not a substitute for the regulation, the manufacturer's manual or your employer's procedures. State plans and site rules can be stricter.