NCCCO LAT • FREE PRACTICE TEST

Lattice Boom Crane (LAT)
Free Practice Test

Lattice boom cranes are assembled from boom sections and pinned in place. CCO certifies crawler and truck-mounted lattice cranes under one designation, LAT.

Reviewed November 2026. 20 questions, answers explained, no sign-up.

CCO's lattice boom designation is LAT, which replaced the older LBC (crawler) and LBT (truck) codes. The specialty written exam has 28 questions in 60 minutes with a calculator allowed. Expect boom assembly, pendants and lattice load charts on top of the Core topics.
NCCCO LAT
Lattice Boom — General
Question 1 of 20

Assembling a lattice crane near a 350 kV power line requires a clearance of…

  1. A20 feet
  2. B10 feet
  3. C45 feet
  4. D4 inches

Exam Format and Fees

ExamQuestionsTimeCalculatorFee
Core written (all mobile cranes)9590 minNo$140
LAT specialty written2860 minYes$80
LAT practical———$70

Sources: CCO Mobile Crane Operator Candidate Handbook, nccco.org/fees.

What This Test Covers

  • ✓Boom sections, pendants and jibs
  • ✓Assembly and disassembly basics
  • ✓Crawler ground bearing and travel
  • ✓Lattice boom load charts
  • ✓Counterweight configurations
  • ✓Wire rope reeving and parts of line

Want the full picture first? Read the lattice boom certification guide.

20 Lattice Boom Practice Questions With Answers

Read through these at your own pace. Pick an answer, then open the explanation. The scored test above deals a different set each time.

Lattice Boom — General

1. Assembling a lattice crane near a 350 kV power line requires a clearance of…

  1. A20 feet
  2. B10 feet
  3. C45 feet
  4. D4 inches
Show answer

Answer: A. 20 feet. During assembly/disassembly, up to 350 kV requires 20 feet of clearance.

Lattice Boom — Load Charts

2. On a lattice-boom friction machine paying out line, per the manufacturer how many full wraps must remain on the drum?

  1. AAt least 2 full wraps (some manufacturers require 3)
  2. B1 full wrap
  3. CHalf a wrap past the anchor
  4. DNo minimum — the rope anchor holds the load
Show answer

Answer: A. At least 2 full wraps (some manufacturers require 3). The rope anchor alone is not designed to hold the load — ASME B30.5 and manufacturer charts require a minimum of two full wraps remaining on the drum at all times; some manufacturers specify three. Always check your chart’s notes.

Lattice Boom — General

3. For liftcrane operations, the LAT machine must be set up level on a firm uniformly supporting surface with the gantry…

  1. ARaised (up)
  2. BLowered for transport
  3. CRemoved
  4. DAt half height
Show answer

Answer: A. Raised (up). The lattice crane operates in a level position on a firm uniformly supporting surface with the gantry up.

Lattice Boom — Load Charts

4. Per the LAT notes, upper boom point capacity with a SINGLE part whip line is…

  1. A29,500 lbs
  2. B59,000 lbs
  3. C20,000 lbs
  4. D40,000 lbs
Show answer

Answer: A. 29,500 lbs. Upper boom point capacity for liftcrane service is 29,500 lbs with single part whip line, or 59,000 lbs with two-part.

Lattice Boom — General

5. According to ASME B30.5, when the control on the far-right hand side of a conventional crane is released to the center position, which action should be expected?

  1. Athe boom hoist will be held stationary
  2. Bthe boom hoist safety pawl will be automatically disengaged
  3. Cthe swing brake will be automatically applied
  4. Dthe load hoist drum will free wheel until the hoist brake is engaged
Show answer

Answer: A. the boom hoist will be held stationary. Per the ASME B30.5 standard control arrangement, the far-right lever is the boom hoist, and releasing it to center must automatically hold the boom stationary.

Lattice Boom — Load Charts

6. Per the LAT notes, when the boom butt mounted auxiliary drum is used, single part whip line capacity becomes…

  1. A20,000 lbs
  2. B29,500 lbs
  3. C40,000 lbs
  4. D12,500 lbs
Show answer

Answer: A. 20,000 lbs. With the auxiliary drum, capacity is 20,000 lbs with a single part whip line, or 40,000 lbs with two parts.

Lattice Boom — General

7. When deviating from manufacturers procedures during assembly, the employer would:

  1. Arequire the use of wire rope slings
  2. Bplace shorter boom sections closest to the base
  3. Cremove top pins first on cantilevered sections
  4. Dprovide adequate support for all parts of the equipment
Show answer

Answer: A. require the use of wire rope slings. When deviating from manufacturer assembly procedures, the employer must provide equivalent protection — here, requiring wire rope slings for handling boom sections, since lattice steel can cut synthetic slings.

Lattice Boom — Load Charts

8. Per the LAT "maximum boom and jib lengths lifted unassisted" table, the longest bare boom that can be raised over the FRONT of blocked crawlers is…

  1. A290 ft
  2. B280 ft
  3. C260 ft
  4. D250 ft
Show answer

Answer: A. 290 ft. Over the front of blocked crawlers the crane can raise up to a 290-ft boom unassisted (though the upper boom point cannot be used on the 290-ft boom).

Lattice Boom — General

9. Unless specified by the manufacturer, the gantry should be in which position when lifting a load?

  1. Ahighest position
  2. Blowest position
  3. Cstowed position
  4. Dmidpoint position
Show answer

Answer: A. highest position. The raised gantry improves the angle of the boom hoist reeving and pendants, reducing compression in the boom and loads in the suspension system.

Lattice Boom — Load Charts

10. Per the LAT notes, 250-ft through 290-ft boom lengths require what change at the lower boom point?

  1. AOnly the middle two sheaves remain — all other sheaves must be removed
  2. BAll sheaves must be replaced with rollers
  3. CThe lower boom point must be removed entirely
  4. DA fifth sheave must be added
Show answer

Answer: A. Only the middle two sheaves remain — all other sheaves must be removed. 250-ft through 290-ft booms require only the middle two sheaves in the lower boom point; all other sheaves must be removed.

Lattice Boom — General

11. Most lattice boom truck cranes performing 'over the front' operations must use:

  1. Aa front mounted outrigger
  2. Ba short boom length
  3. Ctimber matting/blocking under the front bumper
  4. Da front bumper counterweight
Show answer

Answer: A. a front mounted outrigger. Over-the-front capacity on most lattice boom truck cranes requires the front (fifth) outrigger under the carrier front to complete the stability base in that quadrant.

Lattice Boom — Load Charts

12. A 60-ft jib (No. 134) is attached but you are lifting on the main boom. What must be deducted from main boom capacities?

  1. A5,100 lbs
  2. B4,300 lbs
  3. C6,100 lbs
  4. D3,500 lbs
Show answer

Answer: A. 5,100 lbs. The jib-attached deduction table gives 5,100 lbs for the 60-ft jib.

Lattice Boom — General

13. When disassembling lattice boom cranes, it is extremely important to:

  1. Anever remove any pin on any boom section located between the pendant attachment points and the crane
  2. Bdrive the top pins out from the inside of the boom
  3. Calways be positioned inside the boom to drive out the lower pins
  4. Dalways keep the pendants taut and connected at the boom point, while disassembly progresses
Show answer

Answer: A. never remove any pin on any boom section located between the pendant attachment points and the crane. The sections between the pendant attachment points and the crane hold up the suspended boom — removing any pin there lets the boom fall.

Lattice Boom — Load Charts

14. Boom angle and operating radius disagree on a lattice crane. Which value governs capacity?

  1. AThe operating radius, in all cases
  2. BThe boom angle, in all cases
  3. CWhichever gives the higher capacity
  4. DThe boom point elevation
Show answer

Answer: A. The operating radius, in all cases. Boom angle is an indication of operating radius, but in all cases the operating radius shall govern capacity.

Lattice Boom — General

15. According to OSHA 1926.1437, when operating a crawler crane on a barge, it is necessary to:

  1. Aattach the crane to the barge
  2. Breduce the load chart by 20%
  3. Coperate the crane from the front quadrant only
  4. Dreduce the load chart by 30%
Show answer

Answer: A. attach the crane to the barge. OSHA 1926.1437 requires cranes on barges to be physically attached (secured) so the crane cannot shift as the barge lists and trims.

Lattice Boom — General

16. When lifting over the side of a crawler, the tipping axis of the crane will change when:

  1. Atracks are extended or retracted
  2. Bthe wind blows against the back of the boom
  3. Cthe load is raised or lowered
  4. Dthe boom is raised or lowered
Show answer

Answer: A. tracks are extended or retracted. Over the side, the tipping axis is the track centerline on that side; extending or retracting the tracks moves that line and changes the leverage.

Lattice Boom — General

17. On a sagging lattice boom, the line of compression that eventually causes the boom to fail runs between which two points?

  1. AThe boom tip and the boom foot pin
  2. BThe boom tip and the gantry sheaves
  3. CThe boom foot pin and the counterweight
  4. DThe pendant attachment point and the load hook
Show answer

Answer: A. The boom tip and the boom foot pin. As a lattice boom sags, the compressive force travels the straight chord from tip to foot pin while the boom itself bows away from that line. The greater the sag, the greater the bending, until the chords can no longer carry the compression.

Lattice Boom — General

18. When a damaged lacing is cut out of a lattice boom for an approved repair, the cut must be made so that:

  1. AHeat is kept away from the main chords
  2. BThe cut face is left rough for better weld penetration
  3. CThe lacing is removed flush with no stub remaining
  4. DThe adjacent lacings are also loosened
Show answer

Answer: A. Heat is kept away from the main chords. Heat transferred into a chord alters its metallurgy and weakens it. Cutting technique, replacement parts, welding rod, heat treatment, and welder certification must all follow the manufacturer's procedure.

Lattice Boom — General

19. The distance from the boom point to the jib backstay line connection on the boom must be:

  1. AEqual to or greater than the length of the jib
  2. BExactly half the length of the jib
  3. CNever more than 10 feet
  4. DEqual to the boom length
Show answer

Answer: A. Equal to or greater than the length of the jib. That geometry keeps the backstay angle shallow enough to hold the jib mast without overloading the pendants or the boom tip attachment.

Lattice Boom — General

20. For optimum jib pendant loading, how should the jib backstay pendants compare with the jib forestay pendants?

  1. AEqual in length, or the backstays longer
  2. BEqual in length, or the forestays longer
  3. CBackstays always exactly half the forestay length
  4. DIt makes no difference
Show answer

Answer: A. Equal in length, or the backstays longer. Equal-length pendants, or slightly longer backstays, balance the mast loads. Short backstays crank up the tension in the backstay pendants and the mast attachment.

Study the Whole Exam, Not 20 Questions

5,000+ practice questions across Core and every specialty, load chart trainers with the rating table on screen, timed exam simulations, and the pass guarantee.

Lattice Boom Exam FAQ

How many questions are on the LAT specialty exam?
28 questions in 60 minutes, and a calculator is allowed. You also need the 95-question Core exam and the LAT practical to earn the designation.
What is on the LAT written exam?
Site (about 23%), Operations (about 23%), Technical Knowledge (about 19%) and Load Charts (about 35%). Load chart problems use the manufacturer charts supplied with the exam.
How much does the LAT certification cost?
CCO lists $80 for the LAT written exam and $70 for the LAT practical, plus $140 for Core if you don't already have it. See every fee.
Are these the real exam questions?
No. CCO doesn't publish its exam items. These are original practice questions on the same lattice boom topics.
What happened to LBC and LBT?
CCO folded the Lattice Boom Crawler (LBC) and Lattice Boom Truck (LBT) codes into a single Lattice Boom designation, LAT. Older cards may still show LBC or LBT.