OECP Crane Operator Exam
Free Practice Test
The Operating Engineers Certification Program (OECP) written exam is what IUOE members take for crane certification: 75 multiple-choice questions, with load chart work done by hand.
Reviewed November 2026. 20 questions, answers explained, no sign-up.
What is the rated load of a crane?
- AThe maximum static vertical load for which the crane or hoist is designed
- BThe average load handled per shift
- CThe load at which the limit switch trips
- D125% of the test load
Exam Format and Fees
| OECP exam | Questions | Time | Notes |
|---|---|---|---|
| Mobile crane written | 75 | 2 hours | Covers boom truck, lattice boom and telescopic boom cranes |
| Tower crane written | 75 | 2 hours | Separate exam |
| Overhead crane written | 75 | 2 hours | Separate exam |
| Recertification written | 50 | 1.5 hours | One per crane type you hold |
| Practical | — | — | One per crane type, taken after you pass the written |
Sources: OECP Candidate Manual, IUOE Local 150 OECP prerequisites. Local 150 says certification is at no cost to IUOE members in good standing.
What This Test Covers
- ✓Site setup, ground conditions and outriggers
- ✓Power line clearances (OSHA 1926.1408)
- ✓Hand signals and communication
- ✓Rigging, slings and wire rope
- ✓Load chart reading and deductions by hand
- ✓Inspections and OSHA 1926 Subpart CC
Want the full picture first? Read the OECP certification guide.
20 OECP Crane Operator Practice Questions With Answers
Read through these at your own pace. Pick an answer, then open the explanation. The scored test above deals a different set each time.
Definitions
1. What is the rated load of a crane?
- AThe maximum static vertical load for which the crane or hoist is designed
- BThe average load handled per shift
- CThe load at which the limit switch trips
- D125% of the test load
Show answer
Answer: A. The maximum static vertical load for which the crane or hoist is designed. Rated load is the maximum static vertical load for which a crane or an individual hoist is designed; any hook load greater than this is an overload.
Crane Types
2. Truck crane capacities are usually greatest over the…
- ARear
- BFront
- CLeft side
- DRight side
Show answer
Answer: A. Rear. Most truck cranes rate highest over the rear; check the work-area chart.
General Knowledge
3. What does the B10 life of an antifriction bearing represent?
- AThe minimum expected life in hours of 90% of a group of bearings at a given speed and loading
- BThe maximum life of the best 10% of bearings
- CThe average life of all bearings tested
- DThe warranty period offered by the manufacturer
Show answer
Answer: A. The minimum expected life in hours of 90% of a group of bearings at a given speed and loading. B10 life is the minimum expected life in hours of 90 percent of a group of bearings operating at a given speed and loading.
Technical Knowledge
4. Swinging rapidly makes the load…
- ADrift outward, increasing the radius and the tipping moment
- BHang closer to the boom
- CWeigh less
- DRise on its own
Show answer
Answer: A. Drift outward, increasing the radius and the tipping moment. Rapid swing slings the load outward past the boom tip — radius grows, capacity shrinks, and stopping the swing suddenly makes the load swing farther still. Swing slowly and smoothly.
Wire Rope
5. On an ABW crane, running wire rope in service must be removed from service when it shows:
- ASix randomly distributed broken wires in one rope lay, or three broken wires in one strand in one lay
- BOne broken wire anywhere in the rope
- CAny surface discoloration
- DA slightly dusty appearance
Show answer
Answer: A. Six randomly distributed broken wires in one rope lay, or three broken wires in one strand in one lay. For running ropes, the standard removal criteria are 6 broken wires in one lay or 3 in one strand in one lay.
Pitch Diameter
6. Lacking a wire rope manufacturer's guidance, what is the rule-of-thumb minimum (critical) sheave diameter for a given wire rope?
- AAt least 20 times the rope diameter
- BAt least 6 times the rope diameter
- CAt least 10 times the rope diameter
- DAt least 40 times the rope diameter
Show answer
Answer: A. At least 20 times the rope diameter. Below roughly 20:1 the repeated bending and straightening of the wires drives premature fatigue failure. Manufacturer tables list higher preferred ratios for specific rope constructions.
Rigging
7. Which natural fiber rope is the only grade normally accepted for construction rigging use?
- ANumber One grade manila
- BNumber One grade sisal
- CTarred hemp
- DCoir
Show answer
Answer: A. Number One grade manila. Other natural fibers are either too weak or deteriorate too quickly. Good manila is recognizable by its light yellow color; darker color means lower grade and lower strength.
ASME B30.9 (Slings)
8. A synthetic web sling must be removed from service in basic rigging when it shows:
- ACuts, holes, broken or worn stitching, melting, or acid/heat damage
- BA manufacturer's tag that is still attached and legible
- CLight surface dirt from normal use
- DA rated capacity marked in pounds
Show answer
Answer: A. Cuts, holes, broken or worn stitching, melting, or acid/heat damage. Cuts, holes, broken stitching, heat/chemical damage, and a missing tag are removal criteria for synthetic web slings.
Load Calculation
9. What is the approximate weight of stone concrete, and of reinforced stone concrete?
- A144 lbs/cu ft plain; 150 lbs/cu ft reinforced
- B100 lbs/cu ft plain; 110 lbs/cu ft reinforced
- C200 lbs/cu ft plain; 220 lbs/cu ft reinforced
- D62 lbs/cu ft plain; 75 lbs/cu ft reinforced
Show answer
Answer: A. 144 lbs/cu ft plain; 150 lbs/cu ft reinforced. Concrete (stone) is about 144 lb/cu ft; reinforced stone concrete is about 150 lb/cu ft (about 4050 lb per cubic yard).
Load Charts
10. A plate mounted near the boom foot pins gives the distance from those pins to the center of rotation. How is it used?
- AAdd it to the measured distance from the boom foot out to the load center to get the total load radius
- BSubtract it from the boom length to get the effective boom length
- CIt is the minimum allowable radius for the crane
- DIt is used only for calculating ground bearing pressure
Show answer
Answer: A. Add it to the measured distance from the boom foot out to the load center to get the total load radius. Radius is always measured from the axis of rotation to the center of the load. Measuring from the boom foot and adding the plate's fixed offset gives an accurate radius when a tape cannot be run to the rotation center.
Site Setup
11. Why can a truck crane impose higher ground pressure than a crawler crane of similar weight?
- AThe outrigger pads present a much smaller total bearing area than tracks
- BTruck cranes always weigh more than crawlers
- CRubber tires transmit more shock into the soil
- DTruck cranes are always rated at a longer radius
Show answer
Answer: A. The outrigger pads present a much smaller total bearing area than tracks. Ground pressure equals load divided by bearing area. Four small pads concentrate the same machine and load weight far more than two long tracks, so the soil under each pad must be proven capable.
Power Lines
12. Which sequence correctly rebuilds the Table A voltage bands, top to bottom?
- A50 · 200 · 350 · 500 · 750 · 1,000 kV
- B50 · 100 · 200 · 400 · 800 · 1,000 kV
- C50 · 250 · 450 · 650 · 850 · 1,000 kV
- D100 · 200 · 300 · 500 · 750 · 1,000 kV
Show answer
Answer: A. 50 · 200 · 350 · 500 · 750 · 1,000 kV. Voltage climbs +150 (50→200→350→500), then the step doubles-ish to +250 (750, 1,000) — same pivot row where distance shifts from +5 to +10.
Operation Aids
13. An older crane that was built without an operational aid is required to have one installed at what point?
- AWhen the crane undergoes modification or repair
- BImmediately, regardless of its age
- COnly when it is sold to a new owner
- DNever — pre-existing cranes are permanently exempt
Show answer
Answer: A. When the crane undergoes modification or repair. The requirement is not retroactive on its own, but modifying or repairing the machine triggers the obligation to bring it up to the current aid requirement.
Signals
14. On a 'blind lift' where the load is out of the operator's line of sight, the operator should:
- AUse a qualified signal person or other approved communication throughout the lift
- BProceed slowly using best judgment alone
- CLift only if the load is light
- DHave the load moved into view by hand first
Show answer
Answer: A. Use a qualified signal person or other approved communication throughout the lift. When the operator cannot see the load or landing area, a signal person/reliable communication is required.
Operations
15. While slowly lifting, holding or lowering a load on the torque converter, what must the operator avoid doing?
- AEngaging any other clutch, because the added load will make the converter slip
- BIncreasing engine rpm above idle
- CWatching the drum rotation indicator
- DKeeping the hoist clutch engaged
Show answer
Answer: A. Engaging any other clutch, because the added load will make the converter slip. The converter is already near its slip point holding the load. Adding another driven function robs it of torque and the load starts to run away.
Mobile Crane Essentials
16. Cranes on fully extended outriggers are normally rated at 85% of tipping. When a crane is designed to work with its outriggers at an intermediate (partly extended) position, how does the rating percentage for that position compare?
- ALower than 85%, because the crane will tip considerably sooner
- BStill 85%, since the outriggers are set and supported
- CHigher than 85%, since a shorter beam is stiffer
- DNot rated at all — intermediate positions are banned on every crane
Show answer
Answer: A. Lower than 85%, because the crane will tip considerably sooner. Retracting the outrigger beam pulls the tipping axis closer to the center of rotation, so the machine reaches its tipping point at a much lighter load. Charts for the 50% and 0% positions use a lower percentage of tipping than the 85% used at full extension, and the exact figure varies by manufacturer. Older cranes not designed for it had to be rated at 0% extension whenever the beams were not fully out.
Inspections
17. How often does O.S.H.A. require a written wire rope inspection?
- AOnce a month
- BOnce a shift
- COnce a week
- DOnce a quarter
Show answer
Answer: A. Once a month. OSHA 1910.179 requires a thorough inspection of running ropes at least once a month, with a written, dated, and signed report kept on file.
Standards
18. Which ASME standard covers below-the-hook lifting devices such as lifting beams and coil hooks?
- AASME B30.20
- BASME B30.2
- CASME B30.16
- DASME B30.9
Show answer
Answer: A. ASME B30.20. ASME B30.20 is the standard for below-the-hook lifting devices; B30.2 covers overhead and gantry cranes and B30.9 covers slings.
OSHA 1926 Subpart CC
19. According to OSHA 1926.1402, equipment must not be assembled or used unless ground conditions are:
- AFirm, drained, and graded sufficiently to meet the manufacturer's specifications for support and levelness
- BLevel within 5 percent grade in all directions
- CCompacted to 95 percent Proctor density
- DInspected and certified by a registered professional engineer
Show answer
Answer: A. Firm, drained, and graded sufficiently to meet the manufacturer's specifications for support and levelness. 1926.1402(b) requires ground that is firm, drained, and graded so that, with supporting materials if needed, the manufacturer's specifications for adequate support and degree of level are met.
ASME B30.5 (Mobile Cranes)
20. According to ASME B30.5 standard hand signals, EMERGENCY STOP is given by:
- ABoth arms extended, palms down, moving arms back and forth horizontally
- BOne arm extended, palm down, moving back and forth
- CClasping hands in front of the body
- DArm extended, thumb pointing down
Show answer
Answer: A. Both arms extended, palms down, moving arms back and forth horizontally. Figure 5-3.3.4-1 shows STOP as one arm extended palm down moving horizontally, and EMERGENCY STOP as both arms doing that motion.
Study the Whole Exam, Not 20 Questions
5,000+ practice questions across Core and every specialty, load chart trainers with the rating table on screen, timed exam simulations, and the pass guarantee.