SETUP & SITE HAZARDS • CRANE EXAM TOPIC

Crane Counterweight
What It Does and the Rules Around It

Counterweight is what keeps a crane from tipping toward the load. Too little and it tips forward, too much and it can go over backward.

Reviewed November 2026 against 29 CFR 1926.1417(v), 1926.1424, 1926.1401.

A counterweight is weight added to the crane to balance the load and keep it stable. OSHA requires the crane to be operated with the counterweight in place as the manufacturer specifies, and the manufacturer's maximum must not be exceeded. The load chart is only valid for the counterweight configuration it names.

How Counterweight Works

A crane is a lever. The load pulls down on one side of the tipping axis; the weight of the crane, including the counterweight, pulls down on the other. The load's pull is its weight times its radius. As the radius grows, so does the overturning force, which is why capacity drops as you boom out.

More counterweight raises stability against tipping forward. It also adds load to the structure and moves the balance point rearward. With a short boom at a high angle and no load on the hook, too much counterweight can tip the crane backward. That is why the manufacturer's maximum is a hard limit.

The Rules

RuleSource
Do not operate without the counterweight or ballast in place as the manufacturer specifies1926.1417(v)(1)(i)
Do not exceed the maximum counterweight or ballast the manufacturer specifies1926.1417(v)(1)(ii)
During assembly and disassembly, the A/D director must address the hazard of being struck by inadequately supported or hoisted counterweights, and loss of backward stability1926.1404(h)
Train workers on the swing radius hazard and mark the area the rotating superstructure sweeps with control lines, warning lines, railings or similar barriers1926.1424(a)

Counterweight and the Load Chart

Many cranes have several charts, one for each counterweight package. Lifting with less counterweight than the chart assumes is the same as overloading the crane. Before a lift, confirm the counterweight installed matches the chart selected in the LMI and on paper.

Counterweight is part of the crane, not part of the load. You do not deduct it from capacity. What you do deduct is covered in our load chart guide.

On truck and all-terrain cranes, some or all of the counterweight comes off for road travel to stay inside axle weight limits, and goes back on at the site.

5 Practice Questions: Crane counterweight

From the question bank in the app. Pick an answer, then open the explanation. For a scored test, try the NCCCO core practice test.

General Knowledge

1. On a mobile crane, the "counterweight" is:

  1. AWeight attached to the superstructure, typically at the rear, to offset the load moment and improve stability
  2. BExtra weight added to the load to keep it from swinging
  3. CBallast placed on the outrigger floats
  4. DThe weight of the hook block used to overhaul the hoist line
Show answer

Answer: A. Weight attached to the superstructure, typically at the rear, to offset the load moment and improve stability. Counterweights create a moment opposite the load's overturning moment, increasing lifting capacity within the limits the manufacturer designed. Only manufacturer-approved counterweight configurations may be used.

Technical Knowledge

2. Exceeding the manufacturer's maximum counterweight…

  1. ACan cause structural damage and/or tip the crane backwards
  2. BIs fine if the crane doesn't tip forward
  3. CAdds capacity safely
  4. DOnly matters on crawlers
Show answer

Answer: A. Can cause structural damage and/or tip the crane backwards. Extra counterweight overstresses the structure and threatens backward stability.

Operations

3. Operating a crane with its counterweight or ballast NOT in place as specified by the manufacturer is…

  1. AProhibited
  2. BAllowed for loads under 50 percent of chart
  3. CAllowed during travel between lifts
  4. DAllowed if the LMI is active
Show answer

Answer: A. Prohibited. Equipment must not be operated without the manufacturer-specified counterweight or ballast in place.

Site Setup

4. The area swept by the rotating superstructure and counterweight (the crush/pinch zone) must be…

  1. ABarricaded to keep employees out
  2. BLeft open for spotters
  3. CMarked only at night
  4. DKept within 2 feet of a wall
Show answer

Answer: A. Barricaded to keep employees out. 1926.1424 requires the swing-radius crush zone be barricaded; a worker caught between the counterweight and a fixed object can be killed.

Crane Types

5. Why must counterweight be removed or reduced on some truck and all-terrain cranes before road travel?

  1. ATo stay within legal axle weight limits for highway travel
  2. BTo improve lifting capacity
  3. CTo lower the center of gravity for lifting
  4. DTo free-fall the load faster
Show answer

Answer: A. To stay within legal axle weight limits for highway travel. Full counterweight can exceed legal per-axle road weights, so it is often transported separately and reinstalled on site before lifting.

Study the Whole Exam, Not 20 Questions

5,000+ practice questions across Core and every specialty, load chart trainers with the rating table on screen, timed exam simulations, and the pass guarantee.

Crane counterweight: Questions & Answers

What does a counterweight do on a crane?
It balances the load on the hook so the crane stays stable. It offsets the overturning force created by the load weight acting at its radius.
Can you add extra counterweight to lift more?
No. OSHA prohibits exceeding the manufacturer's maximum counterweight. Extra weight can overstress the crane and cause it to tip backward.
What is backward stability?
A crane's resistance to tipping over its rear. It matters most with a short boom at a high angle and little or no load, when the counterweight has the most leverage.
Why is the area behind a crane barricaded?
The counterweight swings with the upper. Anyone between it and a fixed object can be crushed. OSHA requires the swing radius hazard area to be marked off and workers trained to stay out.
Is the counterweight deducted from the load chart capacity?
No. The chart already assumes it. Deductions are for things hanging from the boom: the hook block, rigging, stowed jib and similar items.

This page is a study aid. It summarizes federal OSHA rules and industry standards and is not a substitute for the regulation, the manufacturer's manual or your employer's procedures. State plans and site rules can be stricter.