SETUP & SITE HAZARDS • CRANE EXAM TOPIC

Crane Outriggers
Setup Rules, Pads & Cribbing

How outriggers have to be set, where blocking goes, and what changes when you lift on rubber instead.

Reviewed November 2026 against 29 CFR 1926.1404(q), 1926.1402.

Outriggers must be fully extended, or set to the position the load chart specifies, and set so the crane's weight is off the wheels. Floats must be attached. Each outrigger must be visible to the operator or a signal person while it is extended and set. Blocking goes only under the float or pad, never under the beam.

OSHA Outrigger and Stabilizer Rules

RuleDetail
ExtensionFully extended, or deployed as the load chart specifies if the manufacturer allows it
Weight off the wheelsOutriggers must be set to remove the equipment weight from the wheels. This does not apply to stabilizers
FloatsWhen floats are used, they must be attached to the outriggers or stabilizers
VisibilityEach outrigger or stabilizer must be visible to the operator or a signal person during extension and setting
BlockingSize, amount, condition and stacking must be enough to sustain the loads and keep the crane stable
Blocking locationOnly under the float or pad of the jack. Where there is no jack, under the outer bearing surface of the extended beam

Source: 29 CFR 1926.1404(q).

Outrigger vs Stabilizer

An outrigger lifts the crane clear of its tires so the whole machine sits on the outrigger floats. A stabilizer adds stability but may leave some weight on the wheels, which is common on boom trucks and articulating cranes. The load chart is written for one or the other, so use the chart that matches what the machine has and how it is set.

On rubber means lifting on the tires with outriggers retracted. Ratings on rubber are much lower than on outriggers, and only apply if the manufacturer publishes an on-rubber chart. See pick and carry.

Pads, Cribbing and the Ground

The float concentrates a large share of the crane and load weight on a small area. Pads or cribbing spread that force so the ground pressure stays below what the soil can carry. Bigger pad area, lower ground pressure.

Cribbing has to be tight and level. Gaps between timbers leave the float partly unsupported and cut both stability and capacity.

OSHA also requires the ground to be firm, drained and graded enough, with supporting materials if needed, to meet the manufacturer's specifications for support and level. The controlling entity has to tell the crane user about known underground hazards such as voids, tanks and utilities.

The level of the crane is checked before each shift and after each move and setup.

5 Practice Questions: Crane outriggers

From the question bank in the app. Pick an answer, then open the explanation. For a scored test, try the NCCCO core practice test.

Definitions

1. What distinguishes a stabilizer from an outrigger?

  1. AA stabilizer may not be able to relieve all the weight from the wheels or tracks
  2. BA stabilizer extends farther from the carrier
  3. CStabilizers are found only on crawler cranes
  4. DThere is no difference; the terms are interchangeable
Show answer

Answer: A. A stabilizer may not be able to relieve all the weight from the wheels or tracks. Stabilizers increase stability but may not lift all the machine weight off the wheels or tracks, which is why they are not considered outriggers.

General Knowledge

2. The main reason for using timber blocking under the crane's outrigger pads is to:

  1. Adecrease the applied ground pressure
  2. Bshorten the length of the outrigger jacks
  3. Craise the crane in order to reach higher
  4. Dextend the tipping axis of the crane
Show answer

Answer: A. decrease the applied ground pressure. Blocking spreads the outrigger load over a larger area, decreasing the pressure applied to the ground.

Site Setup

3. According to OSHA 1926.1404, floats/pads must be fastened to the outriggers when:

  1. Aoutriggers are in use.
  2. Bthe operator determines they are needed.
  3. Cmats/blocking are required.
  4. Dbeams are partially extended.
Show answer

Answer: A. outriggers are in use.. OSHA 1926.1404 requires that when outriggers are in use, floats/pads must be attached to the outriggers — it is mandatory, not an operator judgment call.

Site Setup

4. Outrigger blocking or cribbing must be placed under the…

  1. AFloat or pad, never under the outrigger beam
  2. BMidspan of the outrigger beam
  3. CTires
  4. DCounterweight
Show answer

Answer: A. Float or pad, never under the outrigger beam. Blocking goes under the float; placing it under the beam can bend or fail the beam. Trap: never crib the outrigger beam.

Site Setup

5. Before the outriggers are loaded, they must be…

  1. AExtended to the position shown on the load chart being used
  2. BExtended only on the load side
  3. CLeft at mid-extension for flexibility
  4. DSet on the bare tires
Show answer

Answer: A. Extended to the position shown on the load chart being used. Outrigger extension must match the chart in use — fully, intermediate, or retracted as charted; mixing positions voids the rating.

Study the Whole Exam, Not 20 Questions

5,000+ practice questions across Core and every specialty, load chart trainers with the rating table on screen, timed exam simulations, and the pass guarantee.

Crane outriggers: Questions & Answers

Do outriggers have to be fully extended?
Fully extended, or set exactly as the load chart in use specifies if the manufacturer provides ratings for intermediate or retracted positions. Mixing positions that the chart does not cover voids the rating.
Where does cribbing go under an outrigger?
Under the float or pad only. Blocking under the outrigger beam can bend or fail the beam.
Do the tires have to be off the ground?
With outriggers, yes: OSHA requires them to be set to remove the equipment weight from the wheels. Stabilizers are the exception.
What is the difference between an outrigger and a stabilizer?
An outrigger can lift the machine off its wheels. A stabilizer increases stability but may not relieve all the weight from the wheels.
How big should outrigger pads be?
Big enough that the outrigger load divided by the pad area is less than the allowable ground bearing pressure. Use the manufacturer's outrigger loads and the site's soil information. There is no single size that fits every lift.

This page is a study aid. It summarizes federal OSHA rules and industry standards and is not a substitute for the regulation, the manufacturer's manual or your employer's procedures. State plans and site rules can be stricter.