OPERATIONS & LIFT PLANNING • CRANE EXAM TOPIC

Pick and Carry
Traveling With a Load

Pick and carry means traveling with a load on the hook. It is allowed only when the manufacturer says so, and under tighter limits.

Reviewed November 2026 against 29 CFR 1926.1417(u).

Pick and carry is moving the crane with a suspended load. OSHA prohibits it if the manufacturer prohibits it. Where it is allowed, a competent person supervises, decides whether to reduce rated capacity, and sets the load position, boom location, ground support, travel route, overhead clearance and speed. On tires, tire pressure must be what the manufacturer specifies.

What OSHA Requires

RuleDetail
Manufacturer permissionTraveling with a load is prohibited if the manufacturer prohibits it
SupervisionA competent person supervises the operation
CapacityThe competent person determines whether rated capacity has to be reduced
PlanningLoad position, boom location, ground support, travel route, overhead obstructions and speed are all decided before moving
TiresOn equipment with tires, pressure specified by the manufacturer must be maintained
SwingRotational speed must keep the load from swinging out beyond the radius at which it can be controlled

Source: 29 CFR 1926.1417(u).

How It Is Done Safely

  • ✓Use the right chart. Pick and carry ratings are a separate, much lower chart than on-outrigger ratings. If the manufacturer gives no such chart, you do not pick and carry
  • ✓Boom where the manufacturer says. On most rough-terrain cranes that is centered over the front with the swing lock or house lock engaged
  • ✓Short boom, load low and close. The lower the load, the less it can swing
  • ✓Travel slowly on firm, level ground. A small slope or a soft spot shifts the radius and the stability at the same time
  • ✓Use tag lines to control the load, and keep people out of the travel path
  • ✓Watch for power lines and overhead obstructions along the whole route, not just at the pick and the set

On Rubber vs On Outriggers

On outriggers, the crane sits on a wide, rigid base. On rubber, it sits on tires that flex, with a narrower base, so capacity is much lower and changes with boom position.

Carry deck cranes and rough-terrain cranes are built with pick and carry in mind. Many truck cranes and boom trucks are not rated for it at all. The load chart is the only authority. More on setup: crane outriggers.

5 Practice Questions: Pick and carry

From the question bank in the app. Pick an answer, then open the explanation. For a scored test, try the NCCCO core practice test.

General Knowledge

1. According to OSHA 1926.1417, who determines if a crane can be used for a pick and carry operation?

  1. AThe manufacturer
  2. BThe crane crew supervisor
  3. CThe rigger in charge
  4. DThe crane operator
Show answer

Answer: A. The manufacturer. Pick and carry operations are permitted only in accordance with the manufacturer's procedures and ratings.

Operations

2. Traveling with a load is permitted only when…

  1. AThe manufacturer allows it and supplies a pick-and-carry load chart
  2. BThe load is under half of chart capacity
  3. CThe travel distance is under 100 feet
  4. DA tag line is attached to the load
Show answer

Answer: A. The manufacturer allows it and supplies a pick-and-carry load chart. Pick and carry is prohibited if the manufacturer prohibits it; when allowed, the manufacturer provides a dedicated pick-and-carry load chart.

Operations

3. Who must supervise a pick-and-carry operation and decide on load position, travel route, ground support, and speed?

  1. AA competent person
  2. BThe crane oiler
  3. CAny certified operator
  4. DThe steel erection foreman
Show answer

Answer: A. A competent person. A competent person supervises traveling with a load, determines whether to reduce rated capacity, and sets load position, boom location, ground support, route, and speed.

Operations

4. On pick-and-carry operations, keep the boom…

  1. AAs short as possible
  2. BFully extended
  3. CAt maximum angle
  4. DOver the side
Show answer

Answer: A. As short as possible. Short boom, load low and close — that's stable pick-and-carry.

General Knowledge

5. When a crane is traveling with a load, the crane should:

  1. AMove toward the load
  2. BMove away from the load
  3. CBe boomed up as high as possible
  4. DBe boomed down as far as possible
Show answer

Answer: A. Move toward the load. Traveling toward the load keeps it ahead of the crane and helps prevent the radius from increasing or the load from swinging.

Study the Whole Exam, Not 20 Questions

5,000+ practice questions across Core and every specialty, load chart trainers with the rating table on screen, timed exam simulations, and the pass guarantee.

Pick and carry: Questions & Answers

What is a pick and carry crane operation?
Lifting a load and then traveling with it suspended from the hook, instead of setting up on outriggers and swinging it into place.
Who decides if a crane can pick and carry?
The manufacturer. OSHA prohibits traveling with a load if the manufacturer prohibits it, and the ratings come from the manufacturer's pick and carry chart.
Who supervises a pick and carry?
A competent person, who also decides whether rated capacity must be reduced and sets the route, speed, boom position and ground support.
Where should the boom be during pick and carry?
Where the manufacturer's chart specifies. On most rough-terrain cranes that is straight over the front, with the boom as short and the load as low as practical.
Is pick and carry a critical lift?
Many company and site lift procedures classify it that way because stability changes as the crane moves. OSHA's crane rule does not use the term. See crane lift plans.

This page is a study aid. It summarizes federal OSHA rules and industry standards and is not a substitute for the regulation, the manufacturer's manual or your employer's procedures. State plans and site rules can be stricter.