OPERATIONAL AIDS • CRANE EXAM TOPIC

Two-Blocking
And the Anti-Two-Block Device

Two-blocking pulls the hook block into the boom tip. Keep pulling and the rope parts and the load comes down.

Reviewed November 2026 against 29 CFR 1926.1416(d)(3), 1926.1401, 1926.1431.

Two-blocking is when the load block, hook block or overhaul ball contacts the boom tip or upper block. It binds the system, and continued power can break the hoist rope. It happens when you hoist up too far or telescope the boom out without paying out line. Telescopic boom cranes built after February 28, 1992 must have a device that automatically prevents it.

What Causes Two-Blocking

  • ✓Hoisting up until the block reaches the boom tip
  • ✓Telescoping out. Extending the boom pulls the block up toward the tip unless you pay out hoist line at the same time. This is the one that catches people
  • ✓Lowering the boom on cranes where that shortens the line between the block and the tip

Raising the boom does not cause it. The fix when the warning sounds is to do the opposite of what caused it: lower the hook or retract the boom.

OSHA Anti-Two-Block Requirements

CraneRequirement
Telescopic boom cranes made after February 28, 1992A device that automatically prevents damage from two-blocking, at every point where it could occur
Lattice boom cranes made after February 28, 1992A device that either automatically prevents damage and load failure, or warns the operator in time to prevent it
Lattice boom cranes and derricks made after November 8, 2011A device that automatically prevents damage and load failure
Articulating cranes with a load hoist, made after December 31, 1999A device that automatically prevents damage
Any crane hoisting personnelAn automatic prevention device. A warning-only device is not enough

Source: 29 CFR 1926.1416(d)(3). Lattice boom cranes are exempt when used for dragline, clamshell, magnet, drop ball, container handling, concrete bucket, pile driving, and marine work that does not involve hoisting personnel.

When the Device Is Not Working

The anti-two-block device is a Category I operational aid. It must be repaired within 7 calendar days, or within 7 days of receiving parts that were ordered within 7 days of the failure.

Temporary alternative measures until then: clearly mark the hoist cable where the operator can see it, at a point that gives enough time to stop the hoist. On telescopic boom cranes, also use a spotter when extending the boom. On lattice boom cranes, the choice is the marked cable or a spotter.

A warning device sounds an alarm or shows a light. A prevention device disengages the functions that cause two-blocking. Know which one your crane has.

5 Practice Questions: Two-blocking

From the question bank in the app. Pick an answer, then open the explanation. For a scored test, try the NCCCO core practice test.

Definitions

1. Two-blocking on a telescopic fixed cab crane occurs when:

  1. Athe hook block or ball contacts the boom tip
  2. Bthe boom is extended past the chart limit
  3. Cthe outriggers lift the tires clear
  4. Dthe load exceeds 85% of tipping
Show answer

Answer: A. the hook block or ball contacts the boom tip. Two-blocking is contact between the lower load block and the boom-tip sheave assembly; it can part the rope and drop the load.

Definitions

2. If two-blocking occurs and power keeps being applied, the most likely result is…

  1. AFailure of the hoist rope or another component
  2. BThe load line automatically pays out
  3. CThe boom hoist locks and nothing is damaged
  4. DOnly a warning light illuminates with no risk
Show answer

Answer: A. Failure of the hoist rope or another component. Two-blocking binds the system, so continued power can break the hoist rope or damage crane components.

General Knowledge

3. All the following can cause a two-block condition EXCEPT:

  1. Araising the boom
  2. Bextending the boom
  3. Clowering the boom
  4. Dhoisting up
Show answer

Answer: A. raising the boom. Raising the boom increases the distance between hook block and boom tip; hoisting up, booming down, and telescoping out all bring them together.

Operation Aids

4. An anti-two-block WARNING device vs. a PREVENTION system:

  1. AThe warning only alarms; the prevention system stops the motion
  2. BBoth stop the hoist
  3. CBoth only alarm
  4. DThey're identical
Show answer

Answer: A. The warning only alarms; the prevention system stops the motion. A warning device alarms; a prevention system disengages the dangerous function.

Operation Aids

5. Telescopic boom cranes manufactured after which date must have a device that automatically PREVENTS two-block damage?

  1. AFebruary 28, 1992
  2. BDecember 16, 1969
  3. CNovember 8, 2011
  4. DMarch 29, 2003
Show answer

Answer: A. February 28, 1992. Telescopic boom cranes made after February 28, 1992 need an anti two-block device that prevents damage at all points where two-blocking could occur.

Study the Whole Exam, Not 20 Questions

5,000+ practice questions across Core and every specialty, load chart trainers with the rating table on screen, timed exam simulations, and the pass guarantee.

Two-blocking: Questions & Answers

What is two-blocking?
A condition in which the component uppermost on the hoist line, such as the load block, hook block or overhaul ball, comes in contact with the boom tip or fixed upper block. It binds the system, and continued power can fail the hoist rope.
What causes two-blocking?
Hoisting the block up into the boom tip, or extending a telescopic boom without paying out hoist line. On some cranes lowering the boom can also do it.
What is an anti-two-block device?
A switch and weight assembly at the boom tip that senses the block approaching. Depending on the system, it warns the operator or locks out hoist up, telescope out and boom down.
How long do you have to fix a broken anti-two-block?
7 calendar days, with the temporary alternative measures in place until then: a clearly marked hoist cable, plus a spotter when extending a telescopic boom.
Is an anti-two-block required for a man basket?
Yes. Hoisting personnel requires a device that automatically prevents two-blocking, not just a warning.

This page is a study aid. It summarizes federal OSHA rules and industry standards and is not a substitute for the regulation, the manufacturer's manual or your employer's procedures. State plans and site rules can be stricter.