RIGGING • CRANE EXAM TOPIC

Below-the-Hook Lifting Devices
Types, Markings & ASME B30.20

Spreader bars, lifting beams, clamps, magnets and vacuum lifters: what they are, how they must be marked, and why their weight counts.

Reviewed November 2026 against OSHA 29 CFR 1926.251(a)(4), 1926.1401.

A below-the-hook lifting device is a device used to attach a load to a hoist: spreader bars, lifting beams, plate clamps, C-hooks, magnets and vacuum lifters. ASME B30.20 covers marking, inspection and use; ASME BTH-1 covers design. The device must be marked with its rated load, and its own weight counts as part of the load on the crane.

Main Types

DeviceHow it works
Lifting beamOne pick point on top, load hangs from points along the bottom. The beam is loaded in bending. Good where headroom is short
Spreader barSlings from the hook attach to each end. The bar is in compression and keeps the lower slings vertical
Plate clampGrips plate by friction or indentation, often tightening with the load
C-hook and coil lifterCarries coils or similar loads on a horizontal arm
Lifting magnetHolds steel by magnetism. Close-proximity and remotely operated types
Vacuum lifterHolds smooth, non-porous loads with suction pads
GrapplePowered jaws for scrap and bulk material

ASME B30.20 groups them as structural and mechanical lifters, vacuum lifters, lifting magnets, grapples and clamps.

Markings and Design

  • ✓Rated load on the device where it can be read
  • ✓Nameplate: manufacturer, serial number, the lifter's own weight if over 100 lb, rated load, and the ASME BTH-1 design category and service class
  • ✓Designed to ASME BTH-1. A fabricated beam with no engineering behind it is not a rated lifting device
  • ✓OSHA construction rule: special custom-design grabs, hooks, clamps and other lifting accessories must be marked with their safe working load and proof tested to 125 percent of rated load before use

Source for the OSHA rule: 29 CFR 1926.251(a)(4).

What Operators Need to Remember

Its weight is part of the load. OSHA defines the load as the object being hoisted plus the load-attaching equipment. A 1,200 lb spreader bar takes 1,200 lb off what you can pick. Deduct it along with the block and slings.

Use it the way it is rated. A beam or bar is rated for specific pick points and spacing, and a clamp rated for vertical lifts may not be rated for turning plate. Read the nameplate and the manufacturer's instructions.

Inspect it. B30.20 calls for a visual check by the operator before and during each use, plus frequent and periodic inspections with records for the periodic ones.

5 Practice Questions: Below-the-hook lifting devices

From the question bank in the app. Pick an answer, then open the explanation. For a scored test, try the overhead crane practice test.

Below the Hook (B30.20)

1. Under ASME B30.20, what is a below-the-hook lifting device?

  1. AA device used for attaching a load to a hoist
  2. BAny hook attached directly to a crane's load block
  3. CA sling assembly made of wire rope or chain
  4. DThe hoisting machinery unit used for lifting and lowering
Show answer

Answer: A. A device used for attaching a load to a hoist. B30.20 defines a below-the-hook lifting device (lifter) as a device used for attaching a load to a hoist; it may contain slings, hooks, and rigging hardware covered by other B30 volumes.

Standards

2. Which ASME standard covers below-the-hook lifting devices?

  1. AB30.20
  2. BB30.9
  3. CB30.10
  4. DB30.26
Show answer

Answer: A. B30.20. B30.20 covers below-the-hook lifting devices; B30.9 is slings, B30.10 is hooks, and B30.26 is rigging hardware.

Below the Hook (B30.20)

3. According to ASME B30.20, which design standard must the manufacturer verify below-the-hook lifting devices are designed to?

  1. AASME BTH-1
  2. BASME B30.2
  3. CAWS D14.1
  4. DANSI Z535.4
Show answer

Answer: A. ASME BTH-1. All B30.20 chapters require the manufacturer to verify the lifter is designed in accordance with ASME BTH-1, Design of Below-the-Hook Lifting Devices.

Below the Hook (B30.20)

4. How does ASME B30.20 define heavy service?

  1. AService that involves operation within the rated load limit that exceeds the limits of normal service
  2. BAny lift above 50% of rated load
  3. CService involving loads above the rated load limit
  4. DOperation only in corrosive or dusty atmospheres
Show answer

Answer: A. Service that involves operation within the rated load limit that exceeds the limits of normal service. Heavy service is service within the rated load limit that exceeds the limits of normal service; loads never legitimately exceed the rated load.

Below the Hook (B30.20)

5. Before assuming responsibility for using the lifter, what shall the operator demonstrate?

  1. AThe ability to operate the lifter as instructed, and an understanding of standard hand signals when applicable
  2. BCompletion of a written 100-question exam
  3. CFive years of rigging experience
  4. DThe ability to repair hydraulic systems
Show answer

Answer: A. The ability to operate the lifter as instructed, and an understanding of standard hand signals when applicable. The operator shall demonstrate the ability to operate the lifter as instructed before assuming responsibility for using it, and shall demonstrate an understanding of standard hand signals when applicable.

Study the Whole Exam, Not 20 Questions

5,000+ practice questions across Core and every specialty, load chart trainers with the rating table on screen, timed exam simulations, and the pass guarantee.

Below-the-hook lifting devices: Questions & Answers

What is a below-the-hook lifting device?
A device used for attaching a load to a hoist. It can contain slings, hooks and rigging hardware, but the device itself, such as a spreader bar or lifting beam, is covered by ASME B30.20.
What is the difference between a lifting beam and a spreader bar?
A lifting beam hangs from one point and carries the load in bending. A spreader bar hangs from slings at each end and carries the load in compression. Spreader bars are lighter for the same capacity but need more headroom.
Does the weight of a spreader bar count against crane capacity?
Yes. Everything hanging below the boom tip is part of the load, including below-the-hook devices, slings, shackles and the hook block.
Which standard covers below-the-hook lifting devices?
ASME B30.20 for marking, construction, installation, inspection, testing, maintenance and operation. ASME BTH-1 for design.
Do below-the-hook devices need to be load tested?
OSHA's construction rule requires special custom-design lifting accessories to be proof tested to 125 percent of rated load before use. Follow the manufacturer and ASME B30.20 for new, altered and repaired lifters.

This page is a study aid. It summarizes federal OSHA rules and industry standards and is not a substitute for the regulation, the manufacturer's manual or your employer's procedures. State plans and site rules can be stricter.