INSPECTIONS & STANDARDS • CRANE EXAM TOPIC

ASME B30.9
The Sling Standard, Explained

B30.9 is the sling standard: design factors, rated loads, inspection and safe use for every common sling type.

Reviewed November 2026 against OSHA 29 CFR 1910.184, 1926.251.

ASME B30.9 covers lifting slings: alloy steel chain, wire rope, metal mesh, synthetic rope, synthetic webbing and roundslings. It sets a minimum design factor of 4 for alloy chain and 5 for the other types, requires a visual inspection each shift before use and a documented periodic inspection at least once a year, and requires every sling to carry its identification.

Key Numbers From B30.9

ItemRequirement
Design factor, alloy steel chain slings4
Design factor, wire rope, metal mesh, synthetic rope, webbing, roundslings5
Frequent inspectionVisual, each shift before the sling is used
Periodic inspectionInterval not to exceed 1 year, based on use and service
Minimum horizontal sling angle30 degrees, unless the manufacturer or a qualified person approves less
Choker rating when not markedWire rope 75% of vertical, chain 80%, synthetic webbing 80%
Choke pointOn the sling body only, never on a splice or fitting

What It Asks of the People Using Slings

  • ✓Use a sling only if its identification is legible. No tag, no lift
  • ✓Know the load weight and where its center of gravity is
  • ✓Pick the rating for the hitch and angle you are using, not the vertical rating
  • ✓Protect slings from sharp edges and corners. For synthetic slings this is a shall, not a should
  • ✓Do not shorten a sling with knots, bolts or other makeshift methods
  • ✓Keep everyone clear of the load and never stand between the sling and the load as it tightens

Related topics: sling angle, basket hitch, choker hitch.

B30.9 and OSHA

OSHA has its own sling rules: 29 CFR 1910.184 for general industry and 1926.251 for construction. They are older than the current B30.9 and less detailed. In practice the industry rigs to B30.9 and to the sling manufacturer's instructions, which satisfies both.

5 Practice Questions: ASME B30.9 (slings)

From the question bank in the app. Pick an answer, then open the explanation. For a scored test, try the rigger practice test.

ASME B30.9 (Slings)

1. According to ASME B30.9, what is the minimum design factor for alloy steel chain slings?

  1. A4
  2. B5
  3. C3
  4. D6
Show answer

Answer: A. 4. Section 9-1.4 requires a minimum design factor of 4 for alloy steel chain slings; all other sling types in B30.9 require 5.

ASME B30.9 (Slings)

2. What is the minimum design factor required for metal mesh, synthetic rope, synthetic webbing, and roundslings under ASME B30.9?

  1. A5
  2. B4
  3. C7
  4. D10
Show answer

Answer: A. 5. Every B30.9 chapter except alloy chain (which uses 4) specifies a minimum design factor of 5.

ASME B30.9 (Slings)

3. According to ASME B30.9, how often shall the frequent inspection of a sling be performed?

  1. AEach shift, before the sling is used
  2. BWeekly
  3. CMonthly
  4. DBefore each lift regardless of service
Show answer

Answer: A. Each shift, before the sling is used. Frequent inspection is a visual inspection for damage each shift before the sling is used; severe or special service slings should be inspected before each use.

ASME B30.9 (Slings)

4. What is the maximum interval permitted between periodic sling inspections under ASME B30.9?

  1. A1 year
  2. B6 months
  3. C2 years
  4. D90 days
Show answer

Answer: A. 1 year. All chapters state periodic inspection intervals shall not exceed 1 yr; frequency within that is based on use, severity, and experience.

Rigging

5. A synthetic web sling must be lifted over a load with sharp square corners. What does ASME B30.9 require?

  1. ACorner protection (padding or wear pads) SHALL be used between the sling and the edge
  2. BProtection should be used only if convenient
  3. CNo protection is needed for polyester
  4. DDouble the sling and lift normally
Show answer

Answer: A. Corner protection (padding or wear pads) SHALL be used between the sling and the edge. For synthetic slings the standard uses shall: protection from cutting by edges, corners, and protrusions is required, not merely recommended.

Study the Whole Exam, Not 20 Questions

5,000+ practice questions across Core and every specialty, load chart trainers with the rating table on screen, timed exam simulations, and the pass guarantee.

ASME B30.9 (slings): Questions & Answers

What does ASME B30.9 cover?
Slings used for lifting: alloy steel chain, wire rope, metal mesh, synthetic fiber rope, synthetic webbing and roundslings. Each type has its own chapter.
How often do slings have to be inspected under B30.9?
A visual frequent inspection each shift before use, and a periodic inspection by a designated person at intervals not exceeding one year. Severe service calls for shorter intervals.
What is the design factor for slings?
A minimum of 4 for alloy steel chain slings and 5 for every other sling type in B30.9.
Can I use a sling with a missing tag?
No. Missing or illegible identification is a removal criterion for every sling type.
What is the difference between B30.9 and B30.26?
B30.9 covers slings. B30.26 covers the hardware slings attach to: shackles, eyebolts, links, rings, swivels, turnbuckles and rigging blocks.

This page is a study aid. It summarizes federal OSHA rules and industry standards and is not a substitute for the regulation, the manufacturer's manual or your employer's procedures. State plans and site rules can be stricter.