RIGGING • CRANE EXAM TOPIC

Types of Crane Hooks
Uses, Latch Rules & Removal Criteria

The type of hook decides where it can be used, how it attaches and whether it needs a latch.

Reviewed November 2026 against 29 CFR 1926.1425, 1926.1431, 1910.179.

Crane and rigging hooks are grouped by how they attach (eye, clevis, swivel, shank) and by job (sorting, foundry, grab, self-locking, duplex). Hooks are covered by ASME B30.10. A hook comes out of service when the throat has opened more than 5 percent, not to exceed 1/4 inch, or when it is bent, twisted, cracked or worn more than 10 percent.

Common Hook Types

HookWhat it isTypical use
Shank hookThreaded or pinned shank mounted in a blockThe main hook on crane hook blocks and overhaul balls
Eye hookClosed eye at the topPermanently attached to a sling leg or chain
Clevis hookU-shaped top with a pinPinned straight to chain without a connecting link
Swivel hookRotates at the topLets the load be positioned before lifting. Most are not meant to rotate under load
Self-locking (positive locking) hookCloses and locks when loadedWhere a load must not come off the hook, including personnel platforms
Sorting hookLong, tapered tip, no latchSorting and laying out plate, pipe and other items with a hole or lug. Load must be fully seated
Foundry hookWide, deep throat, no latchTrunnions and molds in foundries
Grab hook / slip hookNarrow throat that grips a chain link / wide throat that lets chain slideChain slings
Duplex (sister) hookTwo hooks back to back on one shankLarge crane blocks, to split heavy rigging between two throats

When a Latch Is Required

  • ✓In the fall zone: when workers are hooking, unhooking or guiding a load, or making the initial connection, hooks must have self-closing latches or the equivalent. J-hooks are allowed for setting wooden trusses
  • ✓Hoisting personnel: hooks connecting the hoist line to the platform must be the type that can be closed and locked, eliminating the throat opening, and must be closed and locked
  • ✓A latch is not a load-bearing part. It keeps slack slings from slipping off. The load must sit in the bowl of the hook and must not hold the latch open

Sources: 29 CFR 1926.1425(c) and 1926.1431(g).

When to Take a Hook Out of Service

ConditionLimit (ASME B30.10)
Throat openingIncrease of more than 5%, not to exceed 1/4 inch, or the manufacturer's limit
WearMore than 10% of the original section dimension
Bend or twistAny visible bend or twist from the plane of the unbent hook
Cracks, nicks, gougesRemove from service until a qualified person has evaluated it
LatchDamaged or not working, where a latch is required
MarkingsMissing or illegible manufacturer identification or rated load
Heat, weld spatter, unauthorized repairRemove from service. Hooks are never welded, heated or bent back

OSHA's older overhead crane rule, 29 CFR 1910.179, uses 15% throat opening and 10° of twist. The ASME limits are tighter.

5 Practice Questions: Types of crane hooks

From the question bank in the app. Pick an answer, then open the explanation. For a scored test, try the rigger practice test.

Rigging

1. Under ASME B30.10, a hook must come out of service when its throat opening has increased more than…

  1. A5%, not to exceed 1/4 inch
  2. B10%
  3. C15%
  4. D20%
Show answer

Answer: A. 5%, not to exceed 1/4 inch. Under ASME B30.10, a throat opening increase beyond 5% (not to exceed 1/4 in.), or beyond the manufacturer's limit, means the hook has been overloaded — remove it. The 15% figure is the older OSHA 1910.179/1910.180 general-industry rule, not the ASME criterion.

OSHA 1926 Subpart CC

2. According to OSHA 1926.1433, hooks without latches, or with latches removed or disabled, may be used only when:

  1. AA qualified person has determined it is safer to hoist and place the load without latches and load routes are pre-planned to keep employees out of the fall zone
  2. BThe load weighs less than 500 pounds
  3. CThe lift is indoors
  4. DTaglines are attached
Show answer

Answer: A. A qualified person has determined it is safer to hoist and place the load without latches and load routes are pre-planned to keep employees out of the fall zone. 1926.1433(d)(4)(ii) allows latchless hooks only with a qualified person's determination and pre-planned routes ensuring no employee must work in the fall zone except for hooking/unhooking.

OSHA 1926 Subpart CC

3. According to OSHA 1926.1425, hooks with self-closing latches or their equivalent must be used when employees are in the fall zone hooking or guiding loads, with an exception permitting "J" hooks for:

  1. ASetting wooden trusses
  2. BSteel erection
  3. CConcrete bucket work
  4. DPile driving
Show answer

Answer: A. Setting wooden trusses. 1926.1425(c)(2) requires self-closing latch hooks with an exception allowing J-hooks for setting wooden trusses.

Rigging Hardware

4. What is the actual function of a hook latch?

  1. ARetaining loose slings under slack rigging conditions only
  2. BCarrying part of the load once the throat is closed
  3. CPreventing detachment under full load in all conditions
  4. DReplacing visual verification of hook engagement
Show answer

Answer: A. Retaining loose slings under slack rigging conditions only. ASME B30.10 states latches aid retention of loose slings under slack conditions only, are not antifouling devices, and visual verification of proper hook engagement is still required in all cases.

Rigging Hardware

5. When a hook has a latch, the load must be positioned so that it…

  1. ADoes not restrict the latch from closing
  2. BPresses the latch firmly shut
  3. CRides directly on the latch
  4. DHolds the latch open for quick release
Show answer

Answer: A. Does not restrict the latch from closing. The load must not restrict closure of the latch when a latch-equipped hook is used.

Study the Whole Exam, Not 20 Questions

5,000+ practice questions across Core and every specialty, load chart trainers with the rating table on screen, timed exam simulations, and the pass guarantee.

Types of crane hooks: Questions & Answers

What are the different types of crane hooks?
By attachment: shank, eye, clevis and swivel hooks. By purpose: self-locking, sorting, foundry, grab, slip and duplex hooks.
Do crane hooks need a safety latch?
OSHA requires self-closing latches or the equivalent when employees are in the fall zone hooking, unhooking or guiding a load. ASME calls for latches unless the application makes one impractical.
When must a crane hook be replaced?
When the throat opening has increased more than 5 percent (not over 1/4 inch), wear exceeds 10 percent, or the hook is bent, twisted or cracked.
What is a sorting hook used for?
Sorting and positioning items such as plate or pipe that have a hole or lifting point the long tip can pass through. It has no latch, so the load must be fully seated in the bowl.
Where should the load sit on a hook?
In the bowl, also called the saddle, directly under the centerline. Loading the tip bends the hook open at a fraction of its rating.

This page is a study aid. It summarizes federal OSHA rules and industry standards and is not a substitute for the regulation, the manufacturer's manual or your employer's procedures. State plans and site rules can be stricter.