RIGGING • CRANE EXAM TOPIC

Shackle Types
Anchor, Chain, Screw Pin & Bolt-Type

Two body shapes and three pin styles cover nearly every shackle on a crane job. Each has a job it suits and one it does not.

Reviewed November 2026 against OSHA 29 CFR 1926.251.

Rigging shackles come in two body shapes: anchor (bow) shackles with a rounded bow that can take several sling legs, and chain (D) shackles for straight in-line pulls. Each comes with a screw pin for temporary picks, a bolt-type pin with nut and cotter for long-term or rotating connections, or a round pin. Shackles are covered by ASME B30.26.

Body Shapes and Pin Types

TypeWhat it isUse it for
Anchor (bow) shackleRounded, wider bowMulti-leg slings and loads that pull at an angle. The usual rigging shackle
Chain (D) shackleNarrow, D-shaped bodyStraight-line pulls with a single leg. Not for side loads
Screw pinThreaded pin screws into one earPick-and-place lifts where the shackle goes on and off often
Bolt-typeBolt, nut and cotter pinLong-term or permanent installations, and anywhere the load could rotate the pin
Round pinUnthreaded pin held by a cotterStraight in-line loads only. Not for side loads or multi-leg slings

Side Loading Reduces the Rating

A shackle is rated for a load in line with its centerline. Pulling at an angle to the side reduces it.

Angle of side load from in-lineShare of rated load
0° to 5° (in line)100%
6° to 45°70%
46° to 90°50%

ASME B30.26 values for screw pin and bolt-type shackles. If a shackle must be side loaded, follow the manufacturer's or a qualified person's reduction. Round pin shackles are not side loaded.

Using and Inspecting Shackles

  • ✓Markings: the body shows the manufacturer's name or trademark, the rated load and the size. The pin shows the manufacturer and the grade or material. No markings, no lift
  • ✓Screw pins fully engaged: threads all the way in and tight, shoulder against the shackle body
  • ✓Multiple sling legs go in the bow, never on the pin
  • ✓Keep the included angle between legs at 120° or less, and center the load in the bow
  • ✓Never replace a shackle pin with a bolt. Pins are made of different steel and are part of the rating
  • ✓Keep the load centered. When a shackle hangs on a hook, the pin usually goes on the hook, with spacers if needed so it cannot slide to one side. Do not let a moving rope run across a screw pin, because it can unscrew it
  • ✓Remove from service for missing or illegible markings, a 10 percent or greater reduction in any dimension, bends, twists, cracks, heat damage or damaged threads

5 Practice Questions: Shackle types

From the question bank in the app. Pick an answer, then open the explanation. For a scored test, try the rigger practice test.

Standards

1. Shackles, eyebolts, and similar rigging hardware are covered by which ASME standard?

  1. AB30.26
  2. BB30.9
  3. CB30.23
  4. DB30.5
Show answer

Answer: A. B30.26. ASME B30.26 is the rigging hardware standard.

Rigging Hardware

2. Why should the load applied to a shackle be centered in the bow?

  1. ATo prevent side loading of the shackle
  2. BTo keep the pin from overheating
  3. CTo increase the working load limit
  4. DTo let the pin rotate freely
Show answer

Answer: A. To prevent side loading of the shackle. Centering the load in the bow prevents side loading, which reduces a shackle's capacity.

Rigging Hardware

3. When several sling legs are gathered in one shackle, where should the legs be placed?

  1. AIn the bow — multiple legs should not be applied to the pin
  2. BOn the pin, with the bow to the hook
  3. CSplit evenly between pin and bow
  4. DAnywhere, as long as the pin is torqued
Show answer

Answer: A. In the bow — multiple legs should not be applied to the pin. Multiple sling legs must not be applied to the shackle pin; they belong in the bow.

Rigging Hardware

4. If a shackle must be side loaded, its rated load shall be…

  1. AReduced per the manufacturer's or a qualified person's recommendations
  2. BUsed at full value if the shackle is bolt-type
  3. CDoubled to account for the angle
  4. DIgnored, since side loads are not rated
Show answer

Answer: A. Reduced per the manufacturer's or a qualified person's recommendations. A side-loaded shackle's rated load must be reduced according to the manufacturer or a qualified person.

Rigging Hardware

5. A screw pin shackle is properly assembled when…

  1. AThe threads are fully engaged and tight, with the shoulder in contact with the shackle body
  2. BThe pin is backed off a half turn for easy removal
  3. CThe threads show two turns of exposed thread
  4. DThe pin is welded to the body
Show answer

Answer: A. The threads are fully engaged and tight, with the shoulder in contact with the shackle body. Screw pin threads must be fully engaged and tight with the pin shoulder bearing against the shackle body.

Study the Whole Exam, Not 20 Questions

5,000+ practice questions across Core and every specialty, load chart trainers with the rating table on screen, timed exam simulations, and the pass guarantee.

Shackle types: Questions & Answers

What are the main types of shackles?
By shape, anchor (bow) shackles and chain (D) shackles. By pin, screw pin, bolt-type and round pin.
What is the difference between an anchor shackle and a chain shackle?
An anchor shackle has a rounded bow that accepts several sling legs and angled pulls. A chain shackle has a narrow D-shaped body made for straight in-line pulls.
When should you use a bolt-type shackle?
For long-term or permanent installations, and wherever the pin could be turned by the load. The nut and cotter keep the pin from backing out.
Can you side load a shackle?
Screw pin and bolt-type shackles can be side loaded at a reduced rating: 70 percent up to 45 degrees and 50 percent up to 90 degrees. Round pin shackles should not be side loaded.
Which ASME standard covers shackles?
ASME B30.26, Rigging Hardware. It also covers eyebolts, turnbuckles, links, rings, swivels and rigging blocks.

This page is a study aid. It summarizes federal OSHA rules and industry standards and is not a substitute for the regulation, the manufacturer's manual or your employer's procedures. State plans and site rules can be stricter.