RIGGING • CRANE EXAM TOPIC

Sling Angle
Load Factors & How to Calculate Tension

The flatter the sling, the harder it pulls. At 30 degrees each leg carries double its share.

Reviewed November 2026 against OSHA 29 CFR 1910.184.

Sling angle is measured between the sling leg and horizontal. Tension in each leg is its share of the load multiplied by the load angle factor: 1.155 at 60°, 1.414 at 45°, 2.000 at 30°. Keep slings at 60 degrees or steeper where you can, and do not go below 30 degrees.

Sling Angle Load Factor Chart

Angle from horizontalLoad angle factorTension in each of 2 legs on a 2,000 lb load
90°1.0001,000 lb
75°1.0351,035 lb
60°1.1551,155 lb
50°1.3051,305 lb
45°1.4141,414 lb
35°1.7431,743 lb
30°2.0002,000 lb

Load angle factor = 1 ÷ sine of the angle from horizontal. On the job it is sling length ÷ vertical height from the load to the hook.

How to Calculate Sling Tension

Tension per leg = (load weight ÷ number of legs carrying it) × load angle factor.

Example: a 1,000 lb load on two slings at 45°. Each leg's share is 500 lb. 500 × 1.414 = 707 lb in each leg.

Without a protractor, measure the sling length (L) and the vertical height from the pick points to the hook (H). The factor is L ÷ H. A 10-foot sling with 5 feet of height gives 10 ÷ 5 = 2.0, which is a 30° sling.

With three or four legs, do not assume every leg carries an equal share. On a rigid load, two legs can end up carrying nearly all of it. Size the slings so that any two can hold the load.

Rules of Thumb

  • ✓60° or more is preferred. The penalty is only about 15 percent
  • ✓Below 45° the tension climbs fast. At 30° it has doubled
  • ✓Not below 30° unless the sling manufacturer or a qualified person approves it
  • ✓Flat slings also squeeze the load. The horizontal force that crushes the load inward grows as the angle drops. A spreader bar removes it
  • ✓The angle affects the hardware too. Shackles, eyebolts and hooks are all rated for the direction of pull. See shackle types

5 Practice Questions: Sling angle

From the question bank in the app. Pick an answer, then open the explanation. For a scored test, try the rigger practice test.

Rigging

1. The PREFERRED minimum sling angle, measured from horizontal, is:

  1. A60 degrees or higher
  2. B45 degrees or higher
  3. C30 degrees or higher
  4. D90 degrees exactly
Show answer

Answer: A. 60 degrees or higher. Correct: 60 degrees or higher. The trap is the near-miss 45 degrees — a common industry rule of thumb for other things, but the preferred minimum sling angle is 60.

Rigging

2. As the sling angle from horizontal DECREASES, the tension in each sling leg:

  1. Aincreases
  2. Bdecreases
  3. Cstays the same
  4. Ddecreases only if both legs are equal length
Show answer

Answer: A. increases. Correct: tension INCREASES as the angle flattens. The trap is the direction switch — a smaller angle intuitively sounds like less stress, but low, flat angles multiply leg tension.

Rigging

3. A two-leg sling used at a 30 degree horizontal angle carries what percentage of a single vertical leg's capacity?

  1. A100% — no more than one leg used vertically
  2. B150%
  3. C170%
  4. D200%
Show answer

Answer: A. 100% — no more than one leg used vertically. At 30 degrees the pair is worth 100% of one vertical leg. All the benefit of the second leg has been consumed by the angle, which is the clearest argument for keeping sling angles high.

Load Calculation

4. A 1,000 lb load hangs from two slings, each at a 45-degree horizontal angle. What is the tension in each leg?

  1. A707 lbs
  2. B500 lbs
  3. C1,000 lbs
  4. D354 lbs
Show answer

Answer: A. 707 lbs. Each leg carries 500 lbs vertically; 500 x 1.414 (the 45-degree load angle factor) = 707 lbs.

Rigging

5. The 'included angle' of a sling arrangement is the angle…

  1. ABetween the legs of the sling attached to the load
  2. BBetween one sling leg and the horizontal
  3. CBetween the hook and the load's center of gravity
  4. DBetween the boom and the load line
Show answer

Answer: A. Between the legs of the sling attached to the load. Included angle is the angle between sling legs; the lower the sling angle to horizontal, the larger the included angle becomes.

Study the Whole Exam, Not 20 Questions

5,000+ practice questions across Core and every specialty, load chart trainers with the rating table on screen, timed exam simulations, and the pass guarantee.

Sling angle: Questions & Answers

How is sling angle measured?
From horizontal: the angle between the sling leg and the horizontal plane at the load. Some older tables use the angle from vertical, so check which one a chart uses.
What is the load factor for a 60 degree sling?
1.155. Each leg carries its share of the load multiplied by 1.155.
What is the minimum sling angle?
30 degrees from horizontal, unless the manufacturer or a qualified person approves less. 60 degrees or more is preferred.
How do you calculate sling tension?
Divide the load by the number of legs sharing it, then multiply by the load angle factor for the sling angle. The factor is sling length divided by vertical height.
Why does a lower sling angle increase tension?
Each leg still has to supply the same vertical lift, but a flatter leg is pulling mostly sideways, so it needs more total tension to get the same upward force.

This page is a study aid. It summarizes federal OSHA rules and industry standards and is not a substitute for the regulation, the manufacturer's manual or your employer's procedures. State plans and site rules can be stricter.