CCO RIGGER • FREE PRACTICE TEST

Rigger Level I & II
Free Practice Test

Rigger Level I covers rigging a load when the weight and center of gravity are given. Level II adds working those out yourself and rigging unsupervised.

Reviewed November 2026. 20 questions, answers explained, no sign-up.

The CCO Rigger Level I written exam has 60 questions in 60 minutes. Level II has 50 questions in 60 minutes, and Level II is only valid while Level I is current. Both also require a practical exam.
CCO Rigger
Rigging 1
Question 1 of 20

Using the H-L method, a double basket hitch with vertical legs has a SWL of:

  1. ASWL of a single vertical hitch x 4
  2. BSWL of a single vertical hitch x 2
  3. CSWL of a single vertical hitch x 3
  4. DSWL of a single vertical hitch x H/L x 2

Exam Format and Fees

ExamQuestionsTimeWritten feePractical fee
Rigger Level I6060 min$105$95
Rigger Level II5060 min$105$95

Sources: CCO Rigger program, nccco.org/fees.

What This Test Covers

  • ✓Sling types and hitches
  • ✓Sling angles and tension
  • ✓Shackles, hooks and hardware
  • ✓Removal-from-service criteria
  • ✓Load weight and center of gravity
  • ✓Knots and tag lines

Want the full picture first? Read the Rigger certification guide.

20 Rigger Practice Questions With Answers

Read through these at your own pace. Pick an answer, then open the explanation. The scored test above deals a different set each time.

Rigging 1

1. Using the H-L method, a double basket hitch with vertical legs has a SWL of:

  1. ASWL of a single vertical hitch x 4
  2. BSWL of a single vertical hitch x 2
  3. CSWL of a single vertical hitch x 3
  4. DSWL of a single vertical hitch x H/L x 2
Show answer

Answer: A. SWL of a single vertical hitch x 4. A double basket hitch with vertical legs is rated at 4 times the single vertical hitch; inclined legs use SWL x H/L x 4.

Rigging Hardware

2. When inspecting wire-rope end fittings on an ABW crane, which condition on a shackle requires it to be removed from service?

  1. AA bent pin, spread ears, or visible wear/deformation reducing its rating
  2. BA clean, straight pin that threads fully
  3. COriginal manufacturer markings still legible
  4. DA light film of lubricant
Show answer

Answer: A. A bent pin, spread ears, or visible wear/deformation reducing its rating. Deformation, wear, or a bent/mismatched pin compromises the shackle and requires removal.

Rigging 2

3. What is the basic formula for finding the load on a sling leg when the sling is at an angle?

  1. ALoad on sling leg = vertical load x load angle factor
  2. BLoad on sling leg = vertical load / load angle factor
  3. CLoad on sling leg = total load x number of legs
  4. DLoad on sling leg = vertical load x sling length
Show answer

Answer: A. Load on sling leg = vertical load x load angle factor. Each leg's share of the vertical load is multiplied by the load angle factor for that sling angle to get actual leg tension.

Blocks, Hoists & Pulling Gear

4. The mechanical advantage of a block-and-tackle system equals…

  1. AThe number of parts of line supporting the load
  2. BThe number of sheaves in the upper block
  3. CThe rope diameter in eighths
  4. DThe length of rope reeved
Show answer

Answer: A. The number of parts of line supporting the load. Count every line that actually supports the moving block: four supporting parts means each carries roughly a quarter of the load — a 4:1 mechanical advantage before friction.

Rigging 1

5. For a given sling, a vertical hitch provides what percentage of its basket hitch capacity?

  1. A50%
  2. B100%
  3. C75%
  4. D25%
Show answer

Answer: A. 50%. Capacity in a vertical hitch is 50% of the basket hitch capacity, and the choker hitch is 40% of the basket capacity; the basket is the largest-capacity hitch.

Rigging Hardware

6. When a shoulder eye bolt is loaded at 45 degrees from the axis, its working load must be reduced to what?

  1. A30 percent of rated working load
  2. B75 percent of rated working load
  3. C50 percent of rated working load
  4. DNo reduction is needed for shoulder eye bolts
Show answer

Answer: A. 30 percent of rated working load. For angular lifts the adjusted working load is 30% of rated at 45 degrees and 25% of rated at 90 degrees.

Rigging 2

7. Why must choker rated capacity be reduced when the choke angle is less than 135 degrees?

  1. AThe sling body contact at the choke point reduces sling efficiency
  2. BThe load angle factor becomes greater than 2.0
  3. CThe eye splice pulls out at low angles
  4. DThe rope core is crushed by the hook
Show answer

Answer: A. The sling body contact at the choke point reduces sling efficiency. Contact of the sling body with the end attachment or eye at the choke causes an efficiency loss that grows as the choke angle tightens below 135 degrees.

Blocks, Hoists & Pulling Gear

8. Hand chain hoists (chain falls) are covered by which ASME standard?

  1. AB30.16 — overhead hoists
  2. BB30.5 — mobile cranes
  3. CB30.3 — tower cranes
  4. DB30.20 — below-the-hook devices
Show answer

Answer: A. B30.16 — overhead hoists. ASME B30.16 covers overhead (underhung) hoists including hand chain hoists; lever-operated hoists are B30.21.

Rigging 1

9. In a single basket hitch on a stabilized load, how does the load distribute between the two legs?

  1. AIt equalizes automatically, with each leg supporting half the load
  2. BOne leg carries all of the load
  3. CEach leg carries the full load
  4. DThe distribution cannot be predicted
Show answer

Answer: A. It equalizes automatically, with each leg supporting half the load. On loads having inherent stabilizing characteristics, the basket hitch automatically equalizes with each leg supporting half the load. It cannot be used on loads difficult to balance, because the load can tilt and slip out of the sling.

Rigging Hardware

10. What is the approximate efficiency of a properly prepared wire rope clip eye termination for clip sizes 1/8 inch through 7/8 inch?

  1. A80 percent of the rope's catalog breaking strength
  2. B100 percent
  3. C50 percent
  4. D65 percent
Show answer

Answer: A. 80 percent of the rope's catalog breaking strength. A properly made clip termination is rated at 80% efficiency for sizes 1/8 through 7/8 inch and 90% for sizes 1 through 3-1/2 inch.

Rigging 2

11. Why is a quadruple-leg chain sling rated the same as a triple-leg sling?

  1. ANormal lifting practice may not distribute the load uniformly to all 4 legs
  2. BThe fourth leg is only a back-up safety leg
  3. CQuad slings use smaller chain
  4. DOSHA prohibits using more than three legs at once
Show answer

Answer: A. Normal lifting practice may not distribute the load uniformly to all 4 legs. The quad rating equals the triple rating because in practice the load may not be shared uniformly by all four legs.

Blocks, Hoists & Pulling Gear

12. The hazard that makes lever-type (snap) load binders dangerous to release is…

  1. AThe handle stores spring energy and can snap back violently
  2. BSlow release speed
  3. CRust
  4. DThey weigh too much
Show answer

Answer: A. The handle stores spring energy and can snap back violently. A lever binder holds tension in the handle: released carelessly it whips through its arc with enough force to break bones. Keep your body out of the handle’s path — a ratchet binder releases tension gradually and is the safer choice.

Rigging 1

13. Why is a double choker hitch better suited than a single choker for loose bundles, pipes, and rods?

  1. AThe two spread chokers provide load stability, making the load less likely to tip
  2. BIt grips the load with full 360-degree contact
  3. CIt doubles the sling's rated capacity
  4. DIt eliminates the need for tag lines
Show answer

Answer: A. The two spread chokers provide load stability, making the load less likely to tip. A double choker consists of two single chokers attached to the load and spread apart for stability. Like the single choker it does not completely grip the load, but because the load is less likely to tip it is better suited for loose bundles, pipes, and rods.

Rigging Hardware

14. At a 90-degree angle between the incoming and departing lines on a block, the total load on the block is the line pull multiplied by:

  1. A1.41
  2. B2.00
  3. C1.00
  4. D0.50
Show answer

Answer: A. 1.41. The block loading factor at 90 degrees is 1.41; the factor decreases as the angle between the lines increases, reaching zero at 180 degrees.

Rigging 2

15. When placing two sling legs in a hook, what are the maximum allowable angles?

  1. ANo more than 45 degrees from vertical to the outermost leg, and no more than 90 degrees included angle between legs
  2. BNo more than 60 degrees from vertical and 120 degrees included
  3. CNo more than 30 degrees from vertical and 60 degrees included
  4. DThere is no limit if the hook has a safety latch
Show answer

Answer: A. No more than 45 degrees from vertical to the outermost leg, and no more than 90 degrees included angle between legs. With two legs in the hook, the angle from the vertical to the outermost leg must not exceed 45 degrees and the included angle between the legs must not exceed 90 degrees.

Blocks, Hoists & Pulling Gear

16. Jacks (covered by ASME B30.1) must be used…

  1. AOn solid footing, with the load blocked as it rises — never trust the jack alone
  2. BOn any surface if steady
  3. CWithout cribbing to save time
  4. DOnly in pairs
Show answer

Answer: A. On solid footing, with the load blocked as it rises — never trust the jack alone. Set jacks on solid, level footing, and follow the load up with cribbing so it can never fall farther than an inch or two. Hydraulic jacks can creep or fail — blocking holds what the jack gained.

Rigging 1

17. The working load limit of a synthetic web sling is established by which relationship?

  1. AMaterial breaking strength multiplied by the efficiency of the sewing, divided by the design factor
  2. BMaterial breaking strength divided by the number of plies
  3. CWebbing width multiplied by 1,000 pounds per inch
  4. DMaterial breaking strength multiplied by the design factor
Show answer

Answer: A. Material breaking strength multiplied by the efficiency of the sewing, divided by the design factor. Web slings fail at the splice long before the webbing itself. Because sewing efficiency varies by manufacturer and pattern, two slings of identical webbing can carry very different rated loads.

Rigging Hardware

18. ASME B30.26 covers which category of equipment?

  1. ARigging hardware such as turnbuckles, eyebolts, eye nuts, swivel hoist rings, wire rope clips, wedge sockets, links, rings, swivels, and rigging blocks (not crane blocks)
  2. BOverhead and gantry cranes
  3. CWire rope slings only
  4. DBelow-the-hook lifting devices
Show answer

Answer: A. Rigging hardware such as turnbuckles, eyebolts, eye nuts, swivel hoist rings, wire rope clips, wedge sockets, links, rings, swivels, and rigging blocks (not crane blocks). ASME B30.26 is the rigging hardware standard covering turnbuckles, eyebolts, eye nuts, swivel hoist rings, wire rope clips, wedge sockets, links, rings, swivels, and rigging blocks, but not crane blocks.

Rigging 2

19. The recommended safe horizontal lifting angle for multiple slings in a bridle is

  1. AA 60-degree angle
  2. BLess than 24-degree angle
  3. CA 30-degree angle
  4. DLess than 45-degree angle
Show answer

Answer: A. A 60-degree angle. A 60-degree horizontal sling angle keeps tension in each leg reasonable (about 1.15 times the share of the load); shallower angles dramatically increase sling tension.

Blocks, Hoists & Pulling Gear

20. The force needed to slide a load equals roughly…

  1. AThe coefficient of friction times the load’s weight
  2. BThe load’s full weight
  3. CHalf the load’s weight, always
  4. DThe weight divided by the sling angle
Show answer

Answer: A. The coefficient of friction times the load’s weight. Sliding force ≈ μ × W. Dry steel on steel runs very roughly a quarter of the weight — a 4,000-lb skid takes about 1,000 lb of pull — while rollers cut the effort by roughly a factor of ten.

Study the Whole Exam, Not 20 Questions

5,000+ practice questions across Core and every specialty, load chart trainers with the rating table on screen, timed exam simulations, and the pass guarantee.

Rigger Exam FAQ

How many questions are on the Rigger Level I exam?
60 multiple-choice questions in 60 minutes.
What are the Rigger Level I practical tasks?
Four tasks in 60 minutes: a pre-use rigging inspection, six rigging hitches, rigging connections from task cards, and five knots (sheet bend, clove hitch, inside bowline, square knot, and two half hitches).
Do I need Level I before Level II?
Level II is only valid while your Level I certification is current.
How much does rigger certification cost?
CCO lists $105 for each rigger written exam and $95 for each practical.