Articulating Boom Crane
Free Practice Test
Articulating boom cranes, often called knuckle booms, fold at hinged boom sections and are common on delivery trucks.
Reviewed November 2026. 20 questions, answers explained, no sign-up.
On an articulating (knuckle boom) crane, which of the following raises and lowers the inner boom?
- ANone of the above
- BA wire rope boom hoist drum
- CLattice boom pendant lines
- DA gantry and bail assembly
What This Test Covers
- ✓Knuckle boom geometry
- ✓Stabilizer setup
- ✓Articulating load charts
- ✓Remote and seat controls
- ✓Delivery and material placement
- ✓Daily inspection
Want the full picture first? Read the articulating crane certification guide.
20 Articulating Crane Practice Questions With Answers
Read through these at your own pace. Pick an answer, then open the explanation. The scored test above deals a different set each time.
Articulating Crane
1. On an articulating (knuckle boom) crane, which of the following raises and lowers the inner boom?
- ANone of the above
- BA wire rope boom hoist drum
- CLattice boom pendant lines
- DA gantry and bail assembly
Show answer
Answer: A. None of the above. None apply; articulating cranes position the boom with hydraulic cylinders, not rope boom-hoist systems like lattice cranes.
Articulating Crane — Core
2. The power take-off (PTO) on a truck-mounted articulating crane provides:
- AEngine power to drive the hydraulic pump that operates the crane functions
- BElectrical power to the cab lights only
- CBraking force to the rear axle
- DSignal power to the load chart display
Show answer
Answer: A. Engine power to drive the hydraulic pump that operates the crane functions. The PTO transfers engine power to run the hydraulic pump that powers boom and stabilizer functions.
Articulating Crane
3. On an articulating crane, what is the "knuckle"?
- AThe hinged articulation joint between boom sections that lets the boom fold and bend
- BThe ball on the hook block swivel
- CThe pin securing the crane to the truck frame
- DThe rubber bumper on the stabilizer foot
Show answer
Answer: A. The hinged articulation joint between boom sections that lets the boom fold and bend. The knuckle is the articulating joint (typically between the inner/main boom and outer boom) that gives the knuckle-boom crane its folding geometry.
Articulating Crane — Core
4. When engaging the PTO to operate an articulating crane, the manufacturer's typical procedure calls for the operator to:
- AEngage it with the transmission in the correct position and engine at low/idle speed per the manual
- BEngage it at full throttle for faster response
- CEngage it while driving to the next set-up
- DEngage it only after the load is already suspended
Show answer
Answer: A. Engage it with the transmission in the correct position and engine at low/idle speed per the manual. PTO engagement follows the manufacturer's sequence, generally at idle with the drivetrain in the specified state, to avoid damage.
Articulating Crane
5. On a truck-mounted articulating crane, what is the "PTO" (power take-off)?
- AA device that transfers power from the truck's engine or transmission to drive the crane's hydraulic pump
- BThe remote control transmitter for the crane
- CThe pressure relief valve on the main cylinder
- DThe electrical outlet on the crane base for tools
Show answer
Answer: A. A device that transfers power from the truck's engine or transmission to drive the crane's hydraulic pump. The PTO taps the chassis drivetrain to run the hydraulic pump that powers the crane.
Articulating Crane — Core
6. An overload protection (OLP) system on an articulating crane is designed to:
- AWarn the operator and/or limit function movement as the crane approaches its rated capacity
- BIncrease the rated capacity during heavy lifts
- CReplace the operator's duty to read the load chart
- DAutomatically re-level the stabilizers
Show answer
Answer: A. Warn the operator and/or limit function movement as the crane approaches its rated capacity. OLP monitors loading and warns/limits movement near capacity; it supplements, not replaces, the operator's judgment and the chart.
Articulating Crane
7. What is a "stabilizer" on an articulating crane?
- AAn extendable beam and jack deployed from the crane base to support and level the machine during lifting
- BA gyroscope that damps load swing
- CA weight added to the boom tip
- DA strap securing the boom in transport
Show answer
Answer: A. An extendable beam and jack deployed from the crane base to support and level the machine during lifting. Stabilizers extend outboard and jack down to widen the support base and keep the truck stable during crane operation.
Articulating Crane — Core
8. When operating a permanently attached material-handling fork on an articulating crane, proper load control includes:
- ACentering the load on the fork and clamping/securing it so it cannot shift or fall
- BCarrying the load on one fork tip for better visibility
- CExtending the boom fully before picking any load
- DRemoving the safety catch to speed placement
Show answer
Answer: A. Centering the load on the fork and clamping/securing it so it cannot shift or fall. The load must be centered and secured on the fork to prevent shifting, tipping, or dropping.
Articulating Crane
9. Which of the following are boom components found on a typical knuckle-boom crane?
- AAll of the above
- BAn inner (main) boom raised by hydraulic cylinders
- CAn outer boom articulating at the knuckle joint
- DHydraulic telescoping extension sections
Show answer
Answer: A. All of the above. Knuckle-boom cranes combine an inner boom, an articulating outer boom, and hydraulically telescoping extensions.
Articulating Crane — Core
10. Securing an articulating crane's boom for road transit requires:
- AStowing and locking the boom in its travel position within legal height and width
- BLeaving it partly raised for quick set-up
- CWrapping the hoist line around the mirror
- DCarrying the load on the fork during travel
Show answer
Answer: A. Stowing and locking the boom in its travel position within legal height and width. The boom must be fully stowed and secured within transport clearances before driving.
Articulating Crane
11. An articulating (knuckle-boom) crane differs from a telescopic crane primarily because it:
- Afolds at hydraulic knuckle joints instead of extending sections in and out
- Bhas no load chart
- Ccannot rotate
- Dalways uses a lattice boom
Show answer
Answer: A. folds at hydraulic knuckle joints instead of extending sections in and out. An articulating crane reaches by unfolding inner and outer boom sections at hydraulic knuckle joints, rather than telescoping sections in and out like a hydraulic telescopic crane.
Articulating Crane — Core
12. On an articulating crane with a winch (ABW), a two-block condition occurs when:
- AThe hook block runs up and contacts the boom tip/sheave assembly
- BThe load is set on the ground
- CTwo loads are lifted at once
- DThe stabilizers reach full extension
Show answer
Answer: A. The hook block runs up and contacts the boom tip/sheave assembly. Two-blocking is contact between the hook block and boom-tip sheaves; anti-two-block features prevent the resulting damage/line failure.
Articulating Crane
13. The main relief valve in an articulating crane's hydraulic system helps prevent:
- Aoverloading by limiting maximum system pressure
- Btwo-blocking of the hook
- Ccorrosion of the boom
- Dslewing past 360 degrees
Show answer
Answer: A. overloading by limiting maximum system pressure. The main relief valve limits system pressure, which caps the force the cylinders can generate and gives some overload protection, though it does not replace the load chart.
Articulating Crane — Core
14. The anti-two-block (two-block damage-prevention) feature on an ABW crane functions to:
- AWarn and/or stop the function before the hook block contacts the boom tip
- BIncrease hoist speed near the tip
- CAutomatically add parts of line
- DDisable the overload system
Show answer
Answer: A. Warn and/or stop the function before the hook block contacts the boom tip. The device prevents two-blocking by alerting the operator and/or stopping the offending function.
Articulating Crane
15. A key advantage of the knuckle-boom design is the ability to:
- Afold down and reach over a wall or below the bed to place loads
- Blift far more than a telescopic crane of the same size
- Coperate without any load chart
- Deliminate the need for stabilizers
Show answer
Answer: A. fold down and reach over a wall or below the bed to place loads. The articulating boom folds to reach over obstacles and down below grade or the truck bed, placing loads where a straight boom cannot reach.
Articulating Crane — Core
16. A pre-operational inspection of an articulating crane should include checking:
- AHydraulic lines/cylinders, structural members, controls, and safety devices for defects
- BOnly the tire pressure
- COnly the paint condition
- DOnly the seat adjustment
Show answer
Answer: A. Hydraulic lines/cylinders, structural members, controls, and safety devices for defects. The inspection covers structure, hydraulics, controls, and safety devices to find defects before use.
Articulating Crane
17. When stowing (folding) an articulating crane for travel, the operator should:
- Afollow the folding sequence with no load and seat the boom in its rest/cradle
- Bleave the boom partly extended to save time
- Cstow it with a light load still attached
- Dretract the stabilizers before folding the boom
Show answer
Answer: A. follow the folding sequence with no load and seat the boom in its rest/cradle. The boom must be folded in the specified sequence with no load and seated in its travel cradle; stabilizers are retracted only after the boom is safely stowed.
Articulating Crane — Core
18. A limitation of a manually extended (pull-out) boom extension on an ABC/ABW crane is that:
- AIt reduces the crane's rated capacity and must be applied per the chart for that configuration
- BIt increases capacity at long radius
- CIt has no effect on the chart
- DIt removes the need to check the load weight
Show answer
Answer: A. It reduces the crane's rated capacity and must be applied per the chart for that configuration. Manual extensions lengthen the boom, increasing radius and reducing capacity, and require the correct chart column.
Articulating Crane
19. On an articulating crane rated by load moment, a rating of '10 meter-tonnes' means the crane can lift:
- Aa load whose weight times outreach equals that moment — e.g., 5 tonnes at 2 m or 2 tonnes at 5 m
- B10 tonnes at any reach
- C10 tonnes only at maximum reach
- Dany load up to 10 tonnes regardless of reach
Show answer
Answer: A. a load whose weight times outreach equals that moment — e.g., 5 tonnes at 2 m or 2 tonnes at 5 m. A load-moment rating is weight multiplied by outreach; the same moment allows a heavier load at short reach or a lighter load at long reach.
Articulating Crane — Core
20. A 'working-area' (working-range) load chart for an articulating crane is used to:
- AShow how capacity varies with the load's position around the crane (over the side, front, or rear)
- BList engine maintenance intervals
- CShow the fuel burn per hour
- DGive the truck's road-legal weight
Show answer
Answer: A. Show how capacity varies with the load's position around the crane (over the side, front, or rear). Working-area charts define capacities for different zones around the machine, which can differ by direction.
Study the Whole Exam, Not 20 Questions
5,000+ practice questions across Core and every specialty, load chart trainers with the rating table on screen, timed exam simulations, and the pass guarantee.